Replacing Sensar Bat Wing TV Antenna Cable on a 2010 View DL

Thread Summary

Summarized on:
Original Member Title: Cable replacement for Sensar "bat wing" TV antenna 2010 View DL
This AI-generated summary may contain inaccuracies. Please refer to the full thread for complete details.
A member needed to replace cracked coax insulation and a split roof boot on a 2010 View DL Sensar bat wing TV antenna because they were potential water entry points, not because of signal problems. One member suggested testing continuity and considering sealing the damaged jacket with adhesive, caulk, heat shrink, or other weatherproofing instead of replacing the cable, while another noted that OTA bat wing antenna repair information can be harder to find now.

Another RVer reported finding...
More...

Bnystrom

Senior Member
Joined
Jun 12, 2021
Posts
809
Location
Nashua
The TV antenna cable on our '10 View DL is cracked in several places and the boot on the roof is split, so I need to replace both. It appears that I have to remove the entire antenna mounting plate in order to - hopefully - access a connection where I can attach a new cable.
Has anyone here done this and if so, can you verify that there's a connector under the mounting plate? I can make the cable I need, so that's not an issue.
 
Is this something that is giving trouble or just noted and assuming it is a problem?
Thinking about the coax, the outer mesh layer is often just a ground and not a real problem as it carries no signal. Acting more like a shield for stray interference, is what I am used to seeing.
Tested for more than just the cracks? Good continuity end to end, no cross connection between inner and outer?
 
Here's the thing so many people are ditching OTA TV and especially "Bat Wing" antennas that there's not a lot of info about this kind of thing online.

 
Is this something that is giving trouble or just noted and assuming it is a problem?
Thinking about the coax, the outer mesh layer is often just a ground and not a real problem as it carries no signal. Acting more like a shield for stray interference, is what I am used to seeing.
Tested for more than just the cracks? Good continuity end to end, no cross connection between inner and outer?
The issue is not whether the signal is good or not. The split boot and the cracked cable insulation are potential water leak points. The cable has to be replaced.
 
Here's the thing so many people are ditching OTA TV and especially "Bat Wing" antennas that there's not a lot of info about this kind of thing online.

Everything I've read says that the "bat wing" antennas provide superior performance, and ours works fine. Besides, I'm not interested in spending big money on a new antenna for a TV that we rarely use. The point is that the damaged cable and boot are potential water ingress points.
 
Yes, understand that letting water in is not good but when we deal with this in places I work, it costs way too much to replace the cable. Possibly 8-10 thousand dollars plus lost revenue while down, so we work to keep the water out but not replace the cable until it does become a problem in the cable itself.
Depending on what is going wrong, if it is only the outer cover, we rarely replace it but "invent" something less trouble! If it is somewhere that we can get to it, pulling the outer cover back together as much as we can, clamping and adding super glue to hold it and then silicone caulk and wrapping is more practical. We can often use a heat shrink to keep it all together and make it water tight. Looks ugly but works for years and while there we try to build a cover of some sort to keep the sun and weather from eating it again!
If the cable end is something you can get to and unscrew, I might look at just using the normal heat shrink with some kind of plugging compound added. As it shrinks, it forces the compound into any little cracks it can find to make a really solid seal as it sets.
 
The TV antenna cable on our '10 View DL is cracked in several places and the boot on the roof is split, so I need to replace both. It appears that I have to remove the entire antenna mounting plate in order to - hopefully - access a connection where I can attach a new cable.
Has anyone here done this and if so, can you verify that there's a connector under the mounting plate? I can make the cable I need, so that's not an issue.

A few years ago a malicious tree branch swooped down out of nowhere and snatched my antenna right off the roof. There was a splitter inside the roof that was accessible, and I was able to attach the cable for the new antenna. Check on the Winnebago site and you can find the coax wiring diagram that may help.

I don't know if this is the correct one or not:
 
Yes, understand that letting water in is not good but when we deal with this in places I work, it costs way too much to replace the cable. Possibly 8-10 thousand dollars plus lost revenue while down, so we work to keep the water out but not replace the cable until it does become a problem in the cable itself.
Depending on what is going wrong, if it is only the outer cover, we rarely replace it but "invent" something less trouble! If it is somewhere that we can get to it, pulling the outer cover back together as much as we can, clamping and adding super glue to hold it and then silicone caulk and wrapping is more practical. We can often use a heat shrink to keep it all together and make it water tight. Looks ugly but works for years and while there we try to build a cover of some sort to keep the sun and weather from eating it again!
If the cable end is something you can get to and unscrew, I might look at just using the normal heat shrink with some kind of plugging compound added. As it shrinks, it forces the compound into any little cracks it can find to make a really solid seal as it sets.
Today I checked it out and I could see the connector from the antenna in the roof, but there was no way to angle it so I could pull it out and detach it. Consequently, I had to remove the lap sealant, then the screws, and use a thin putty knife to break the silicone bond between the base plate and the roof. I spent a lot of time removing the silicone residue so I could get a solid bond when I reinstalled the base plate. It was a pretty simple matter to feed a new cable with a new boot the antenna mast, then add a sealed connector to the top end. I connected the other end of the new cable in the roof and pushed it back in, but I should be able to remove it should I ever need to (highly unlikely). Overall, it was a pain to do, but it's fixed now and I'm glad to have it behind me.
 
Last edited:
A few years ago a malicious tree branch swooped down out of nowhere and snatched my antenna right off the roof. There was a splitter inside the roof that was accessible, and I was able to attach the cable for the new antenna. Check on the Winnebago site and you can find the coax wiring diagram that may help.

I don't know if this is the correct one or not:
Those diagrams do indicate a "coax adapter", which is what I found in the roof. Thanks for the link!
 

Try RV LIFE Pro Free for 7 Days

  • New Ad-Free experience on this RV LIFE Community.
  • Plan the best RV Safe travel with RV LIFE Trip Wizard.
  • Navigate with our RV Safe GPS mobile app.
  • and much more...
Try RV LIFE Pro Today
Back
Top