2017 View Slide Power Question

Thread Summary

Summarized on:
Original Member Title: 2017 View Slide Power Question
This AI-generated summary may contain inaccuracies. Please refer to the full thread for complete details.
A member's 2017 View slide operates only when the engine is running, prompting a question about why shore power or the house batteries will not run it. Winnebago support said the engine should be running to provide sufficient power for the slide motors; another member noted that an ignition sensor prevents slide operation without the engine running, regardless of available shore power. The operator's manual also calls for the parking brake to be set. Members questioned why shore power could...
More...

TimothyPaul

Advanced Member
RV LIFE Pro
Joined
Aug 2, 2025
Posts
92
Location
Florida
Hi All,

On my 2017 View I can only get the slide to work if the vehicle motor is running. I would think it should work on shore power, or even off the battery. (As long as there is enough power). When I was looking on Winnebago’s site, it looked like it would run off any 12v source. ( of course parking brake on).
Thoughts?
 

Attachments

  • IMG_7464.png
    IMG_7464.png
    665.5 KB · Views: 25
From Winnebago Support

“Hello Timothy,


The slide is designed to work with the engine running as to ensure there is enough power supply to the slide to operate. The slide motors take a large amount of energy to move due to the weight of the slide. It is not recommended to use the slide under shore power or battery alone.



Morris | Customer Care
Winnebago Motorhomes“
 
It gets back to what is actualy happening when we use motors and batteries. We may start a big item with less than best power but it does work to overheat them and make them fail sooner. Maybe not this year but a couple years down the road, perhap?
So that leaves me a bit surprised for this day and age that they are upfront about what is recommended, even to the poiint of making sure we do it right! GOOD on them for that!
The problem with many battery situations is the way batteries operate. We can only see what is at the posts and that is what we get to power things. The problem is that powere tends to move slowly while we may use it quickly! Slide take lots of power so we might look at in this way.
If we were pulling syrup out of a container and pulling it out faster than more can run into that spot, we gradually get less and less power right at the spot where we take it out.
If we could "see" the power clearly at the posts, we would see a definite "divot" or hole form and that means we get less and less actual power if we use battery alone. That is why it has always been best practice to start the engine when using heavy duty power.
The difference is that the engine alternator can make more power available at the post than the slide needs, so it doesn't have to work with low power that creates more heat than is good!
Always been that way but often part of the info that is ignored as people don't see smoke rising, so they think it is fine to continue to abuse their RV!
 
Thank you for that analogy, it makes sense. I guess I am a bit confused on why you can’t use shore power though. Before I purchased my View, I rented several RV’s and the slides worked on shore power. I believe one worked on battery also.

From my limited knowledge of electrical design, I presume it is the amperage that would be an issue ?
 
I'm not sure of that part either as the converter powered by the cord would be something I would expect to add enough power to get the job done in close to the same way the generator will.
One item we often overlook when looking for the best power is howit all ties together when we have the engine running. Depending on age, etc. of each RV, most have a system which ties the chassis battery with the altenator adding to it and both connected to the coach batteries! So when we run the engine we DO get the beneftis of both sets of batteries as well as the alternator working to keep both charged!
But when I look at some specs on your converter, it shows 45 amp ossible output. I know your engine alternator will do 150 amp or so, meaning that the combo of those two added to both sets of chassis and coach batteries, means we have a massive amount of power available. And the kicker from my limited amount of design thought is that the slides are limited to using 30 amps! Seems like they wabt to stuff and elephant through a keyhole!!
Possible thought that the wiring from the converter to the slide motors might be smaller at some point? But I might also guess that it is just a less complex reason like they feel it is not necessary to add the cost involved in letting us use either source?
I may be reaching some sort of level in my aging that leaves me changing my world view? At times I have not considered value nearly as much as I do now. When twenty, I had no money but tended to buy lots of things that were close to a total waste! Now, I tend to look at things and call them a scam way more often!
The more I learn, the less I understand, at times!
 
It's best to follow the instructions in your Operator's Manual. Both the slides (and jacks, if you have them on your View ) instruct you to have the parking brake set and the engine running to operate these items.

And, to insure that you follow those instructions there is an ignition sensor that monitors your running engine and without it sensing that condition the slide will not operate - regardless of if there is enough power when on shore power or not.
 
I'm fully in favor or reading the manual fopr details but then when I look at those manuals, it seems the folks who wrote them have never gone back to read them and ask if they could be improved!
In many cases, I find looking att he manual is one way to may people never read them again as they ahave so many bogus errors!
This question could very likely to come up when the slide fails to operate, so it might be logical to look in the index for troubleshooting slide operation? So we might drop down to page 10-3 where it tells us what to do to check the operation and what we find is not what they recommend at two places on page 10-1!
From page 10-1 and only helpful if we read and remember the whole chapter!
slide2.jpg

slide 3.jpg

But if we want to start with troubleshooting the system, this is what we find on page 10-3!
slide 1.jpg

I can't fault new folks too much if they don't read the manual as it seems the folks who WROTE it never read it again either??
One of the problems I find in the different industries I get involved with is how often the manuals are written by people who fall into two groups. They are often written by people who know the system too well and have no idea what they left out for folks who don't build the item. The other option seems to be written by folks who have never actually tried to work on what they write about!
It seems like pages 10-1 and 10-3 were written by folks who never read what the other person said to do!
 
Hi All,

On my 2017 View I can only get the slide to work if the vehicle motor is running. I would think it should work on shore power, or even off the battery. (As long as there is enough power). When I was looking on Winnebago’s site, it looked like it would run off any 12v source. ( of course parking brake on).
Thoughts?
In addition to saving your batteries it also prevents accidental closure should someone mistake the slide control for a light switch or a child just being curious or playful.
 
I'm fully in favor or reading the manual fopr details but then when I look at those manuals, it seems the folks who wrote them have never gone back to read them and ask if they could be improved!
In many cases, I find looking att he manual is one way to may people never read them again as they ahave so many bogus errors!
This question could very likely to come up when the slide fails to operate, so it might be logical to look in the index for troubleshooting slide operation? So we might drop down to page 10-3 where it tells us what to do to check the operation and what we find is not what they recommend at two places on page 10-1!
From page 10-1 and only helpful if we read and remember the whole chapter!
View attachment 2526782
View attachment 2526783
But if we want to start with troubleshooting the system, this is what we find on page 10-3!
View attachment 2526784
I can't fault new folks too much if they don't read the manual as it seems the folks who WROTE it never read it again either??
One of the problems I find in the different industries I get involved with is how often the manuals are written by people who fall into two groups. They are often written by people who know the system too well and have no idea what they left out for folks who don't build the item. The other option seems to be written by folks who have never actually tried to work on what they write about!
It seems like pages 10-1 and 10-3 were written by folks who never read what the other person said to do!
Yea, notice how they say “we recommend”. Too me sounds like it is a good idea, but not necessarily.
 
This is interesting, as the slide in our 2010 View DL has always worked fine on the batteries alone, even when we only had 85Ah lead-acid batteries in it. The only time I've needed to start the engine to pull in the slide was if the batteries were too low. Since upgrading to 600Ah of LiFePO batteries, that's no longer and issue.
 
In addition to saving your batteries it also prevents accidental closure should someone mistake the slide control for a light switch or a child just being curious or playful.
I kinda of agree, I am not familiar with other buildouts, but on my View, the slide Switch is up very high on the panel above the fridge. It is definitely not accidentally getting activated, and no way a kid could get to it.

I wouldn’t care about the engine running if they had put a switch up at the dash board. But now, it’s park, level, getup and walk to the back to open the slide, go back up front and turn off ignition, then go out and do shore hookups. A lot of extra steps…. And like i mentioned, I have rented several RV’s where the slides worked on all power sources.
 
This is interesting, as the slide in our 2010 View DL has always worked fine on the batteries alone, even when we only had 85Ah lead-acid batteries in it. The only time I've needed to start the engine to pull in the slide was if the batteries were too low. Since upgrading to 600Ah of LiFePO batteries, that's no longer and issue.
Yes, makes sense. No idea why Winnebago would have changed the design.
 
I'm fully in favor or reading the manual fopr details but then when I look at those manuals, it seems the folks who wrote them have never gone back to read them and ask if they could be improved!
In many cases, I find looking att he manual is one way to may people never read them again as they ahave so many bogus errors!
This question could very likely to come up when the slide fails to operate, so it might be logical to look in the index for troubleshooting slide operation? So we might drop down to page 10-3 where it tells us what to do to check the operation and what we find is not what they recommend at two places on page 10-1!
From page 10-1 and only helpful if we read and remember the whole chapter!
View attachment 2526782
View attachment 2526783
But if we want to start with troubleshooting the system, this is what we find on page 10-3!
View attachment 2526784
I can't fault new folks too much if they don't read the manual as it seems the folks who WROTE it never read it again either??
One of the problems I find in the different industries I get involved with is how often the manuals are written by people who fall into two groups. They are often written by people who know the system too well and have no idea what they left out for folks who don't build the item. The other option seems to be written by folks who have never actually tried to work on what they write about!
It seems like pages 10-1 and 10-3 were written by folks who never read what the other person said to do!
I think after my next adventure, I may look at rewiring the slide motors to be on all power sources. Originally I was thinking of adding a DPDT switch to the dashboard of the vehicle o I could activate the slide from the drivers seat, now I am thinking it may be easier to rewire the power sources.
 
I kinda of agree, I am not familiar with other buildouts, but on my View, the slide Switch is up very high on the panel above the fridge. It is definitely not accidentally getting activated, and no way a kid could get to it.

I wouldn’t care about the engine running if they had put a switch up at the dash board. But now, it’s park, level, getup and walk to the back to open the slide, go back up front and turn off ignition, then go out and do shore hookups. A lot of extra steps…. And like i mentioned, I have rented several RV’s where the slides worked on all power sources.
I have a Vista and the switch is up high as is the control for the drop down bed. The bed will work no matter what but they have a key switch to prevent children from using it, if you remove the key which I have never done. Honestly with the power the slide draws I prefer the engine run but I have a “super slide” with two motors. Also, some motorhomes have more than one slide so to put them all out would use a lot of power. Not a problem if you’re on shore power, but if you are dry camping, it will reduce the amount of time you can stay on the battery. Also, the engine has to be running to drop the jacks which needs to be done before I put out the slide so it’s not really a big deal to have the engine running for me.
 
What is often missed is the small details of what we might be doing without knowing it. When we use a motor and it gets the best voltage, it moves and does the operation using less current! Seems backwards and doesn't fit a lot of our thinking but that low voltage and high current is far more likely to damage something! We are all trained to think high voltage burns things out, right? But if we use higher current than normal it may not be a big burst of smoke and flame like high voltage, more just a bit of the shellac that keeps the small wires insulated in the motor may melt down. melt a bit today, a bit next week and at some point the motor fails! But it happens at such aslow rate that we never connect the two details to spot the motor failure may be because we did not start the engine to give that small motor the best chance at a longer life!
This took me quite a long time to figure out but doing repair after storms finally opened me to this idea as it does sound wrong that low voltage is more harm than high, up to a point!
Starting the RV engine is one way to let alll the gizmos that regulate the voltage and current do thier jobs. That can save having to change a slide motor two years later! Motors may not "burn out" in a puff of smoke but more often die from a thousand cuts!
What we really want is not high, nor low voltage but the CORRECT voltage and when we deal with battery power alone, we know for fact that voltage changes any time we use it. So one way to keep the voltage motors get is to always have a steady supply that is regulated to maintain the correct level all the time we are drawing power.
 
Years ago, shortly after buying my 16 View I discovered this issue with the slide safety parameters. I disabled these ‘safety’ features in favor of common sense. As a result I can open and close the slide whenever I choose regardless of whether the engine is running or the E brake is on.
As has already been noted, the control switch is located high enough that children cannot reach it and adults are expected to have enough ‘common’ sense for using it. 10 years in and still using common sense protocols.
 
Always, the user choice and we all get to decide but I always keep in mind how much money shops make to change those motors that fail after a few years of abuse we can't see and don't think about!
A way to possibly get a different view of what we are doing is to watch the voltage right at the battery posts as we move the slide. Keeping in mind that the slides draw power that comes directly off the posts, not whaty is stored way down deep in the battery where we may still have plenty of power stored. They can only access what they find at the posts! If we start with a good fully charged battery and watch the voltage as the slide moves, it may give you a different idea of what voltage you are using to operate the slide motors. Low voltage means high current! High current means high heat.
 
Last edited:

Try RV LIFE Pro Free for 7 Days

  • New Ad-Free experience on this RV LIFE Community.
  • Plan the best RV Safe travel with RV LIFE Trip Wizard.
  • Navigate with our RV Safe GPS mobile app.
  • and much more...
Try RV LIFE Pro Today
Back
Top