2016 Aspect 27K Wiring Mix-Up and 12V Power Loss

Thread Summary

Summarized on:
Original Member Title: Help! I messed up the wiring 2016 Aspect 27K
This AI-generated summary may contain inaccuracies. Please refer to the full thread for complete details.
A member’s 2016 Aspect 27K lost all 12V power under heavy loads, including macerator use and generator starting, and replacing the battery-disconnect relay did not help. Bypassing and then reconnecting the adjacent battery-boost solenoid on a lithium, solar and DC-to-DC charging setup led to chassis-battery drain, disabled jacks and slides, and charging problems.

Members suggested tracing cable identities and checking charging voltage; moving a cable between solenoid posts restored the...
More...

RV_Lee

Senior Member
Joined
Mar 24, 2021
Posts
1,082
I had a 12v system issue when any large draw would kill the whole system. The macerator pump or trying to start the generator. I ordered a new "salesman switch latching relay" and installed it yesterday but it made no difference. Right beside it in my coach is the battery boost solenoid which is still hooked up somehow but I have lithium / solar and a dc to dc charger.

I jumped that solenoid (all cables put on one lug) and the coach came back to life. Then I realized I am probably draining the house battery now, so I disconnected the negative cable and yes, the coach died. So I "un-bypassed" it and put the cables back - but I did it wrong! I now have a dead chassis battery. I have attached photos of what I am working with
 

Attachments

  • 1000016866.jpg
    1000016866.jpg
    177.6 KB · Views: 47
  • 1000016869.jpg
    1000016869.jpg
    112 KB · Views: 42
  • 1000016868.jpg
    1000016868.jpg
    156.5 KB · Views: 42
  • 1000016867.jpg
    1000016867.jpg
    155.7 KB · Views: 41
I'm not the one you truly need for this fix as I have little experience with the change to lithium nor solar. Only know what I read here and have looked at the OEM a lot to understand it! So maybe some point that I do feel I understand and pass some good info on what was first built there but little idea of what changes may be involved?
One is to ID the cables that Winn installed and marked with tape on the cable ends.
I can tell you about what I do see but not much help on whatis needed to get it back to working, maybe small hints can help!
One is this list that helps to ID some of the cables and where they led when as built:
batty cable.jpg

But I don't see what I expect and there is one which I'm not sure what I am seeing is correct?
solenoid 1.jpg

Am I missing what I should see here? are those two small wires labeld LR and FM actually tied to the left big post?
solenoid 2.jpg

Normally LR gets battery when the engine starts or we push a boost switch near the driver to get a jump start. power normally comes from the dash to here on LR, goes though a coil in the solenoid and meets ground both on the mounting bolt and wire FM which is also ground! For adding lithium, folks often do not want the lead acid chassis battery tied straight to the lithium, so they disable this solenoid. That would explain why no wire of the small center connection! But if I see them both connected to the big post, that is not something I understand and would expect it to connect hot wire LR directly to ground wire FM when we start the engine! Looks wrong from here but I'm not the best on what they may have been aiming to do. Often folks take LR off to keep left and right big posts seperated and they may put a toggle switch in that wire for when they might want it for a temporary jump start for a weak chassis battery!

But that may be lots of guessing and not seeing things correctly?
 
The cables on the left lug of the solenoid are from chassis battery and the other one with the fuse is from the dc to dc charger. That is all that is on the left lug.

Right lug has house battery (yellow strap), a bridge cable to the battery on/off relay and the 3rd red cable goes off through the wall. There is also a small yellow wire on the right lug as well.

The dc to dc charger is dead and the leveling jacks and slides dont work either.

I am now plugged in at a park.

I removed the fuse from the left lug dc to dc cable as a precaution
 
With no wire on that middle post, between the red wires, the whole system should be dead. That is the wire that actuates the solenoid. I also removed that wire and jumped around the solenoid for my DC-DC charger. I have has no issues.
 
With no wire on that middle post, between the red wires, the whole system should be dead. That is the wire that actuates the solenoid. I also removed that wire and jumped around the solenoid for my DC-DC charger. I have has no issues.
Thats what I am wondering, I was under the assumption this thing was deleted when the dc to dc got installed. So what is it even being used for now? I did jump it and it was running down the chassis battery, so I re-installed the wires as they were (I think!) and it still killed the chassis battery. I truly am at a loss here!

I am plugged in at an RV park now, my house battery isn't charging, the jacks/slides don't work. I unhooked the negative terminal on chassis battery so it doesn't die again
 
There is a large wire that goes from the fuse box to the side of the solenoid that is turned off, opposite the battery wire. With the solenoid turned off the power cant get to the battery. I would disconnect the DC-DC and revisit the whole system with a clear mind. Get it back to factory and make changes again. Mine is 22 years old but the battery system is similar. I also went for Lithium and a DC-DC but I pulled the convertor, even though it was Lithium capable and put in a Victron Multiplus. In order to keep the functionality of the shut off switch, I had to run a wire from the bus bar back to the solenoid. It was originally in the fuse panel where the old convertor hooked in. It was labeled what it did and mine had a set of DC breakers for the larger loads, it had a 30 amp breaker, one of the small round ones with the number on the button. It was a Green 8 gauge wire.
 
I am going to call around and try to get a pro to take a look at it tomorrow / as soon as possible. If the wiring is the same as it was its going to have to be looked at from stem to stern and tested / diagnosed.
 
Are you sure that the wire with the blue identifier goes to the chassis battery? What if it goes to the jacks, and the red one that you said goes thru the wall goes to the chassis battery/starter? If that were the case the jacks and DC-DC would both be dead as they are now, and your chassis battery would be connected to your house battery as I believe you said it was. I think the red wire that disappears into the wall needs to go on the left with the other 2 that are already on that post. You can verify by removing the red wire and testing it for voltage and see if that voltage goes away when you disconnect the chassis positive.
 
Are you sure that the wire with the blue identifier goes to the chassis battery? What if it goes to the jacks, and the red one that you said goes thru the wall goes to the chassis battery/starter? If that were the case the jacks and DC-DC would both be dead as they are now, and your chassis battery would be connected to your house battery as I believe you said it was. I think the red wire that disappears into the wall needs to go on the left with the other 2 that are already on that post. You can verify by removing the red wire and testing it for voltage and see if that voltage goes away when you disconnect the chassis positive.
I'll try this and let you know what happens, that does make good sense. Thank you
 
Okay, getting into the parts I have never studied or done much looking! So don't take this to the bank!
But one we can say for pretty sure is that the big lugs on each side of the solenoid are not connected inside in any way without the small lugs to the coil being connected! Basicly makes the solenoid a set of lugs where cables can meet! Isolated points where cables can be placed.
What is the DC to DC meant to do? No info/experience on that point for me! But if the blue taped cable on left big lug feeds the jack pump and it is dead as well as the DC to DC, where does that DC gizmo get power to feed the jacks? Sounds like it is not getting power?
But I am way out of what I know much about! We may have to way for folks more experienced with the change to lithium to come along and add to the question. Is that a fuse holder sticking up that might need to be checked?
Have you tested that you still have chassis battery?

Wrote this up last night but got called and failed to get back to it!
what you currently have is the solenoid is no longer functioning. It is just being used as two points to tie wires down! If the two small white wires are not used, they should just be taped and stored ut of the way, not tied together.
But the main problem after things are changed is figuring out how and what the last person did and how they wanted it to work!
That gets into a whole different ballgame with lots of weird stuff being done. When the new change was done, did those folks get the other wiring change figured correctly?
Kind of having a set of parts and each person has to figure out what the last one did?
If they were building a car, did they put the engine in front or back, type situation, with no drawings to follow!
 
Are you sure that the wire with the blue identifier goes to the chassis battery? What if it goes to the jacks, and the red one that you said goes thru the wall goes to the chassis battery/starter? If that were the case the jacks and DC-DC would both be dead as they are now, and your chassis battery would be connected to your house battery as I believe you said it was. I think the red wire that disappears into the wall needs to go on the left with the other 2 that are already on that post. You can verify by removing the red wire and testing it for voltage and see if that voltage goes away when you disconnect the chassis positive.
Big thank you, your advice helped big time because it worked! I moved the wire you said from the left to right and the slides and jacks are working again. Thank you!!

Not totally out of the woods just yet though, the house battery doesn't seem to be charging off shore power and the dc to dc charger is still down as well, but the unit itself is back on. The on/off light is flashing. Its still connected to the left lug of the solenoid.

I don't know how shore power ties into this either
 
Big thank you, your advice helped big time because it worked! I moved the wire you said from the left to right and the slides and jacks are working again. Thank you!!

Not totally out of the woods just yet though, the house battery doesn't seem to be charging off shore power and the dc to dc charger is still down as well, but the unit itself is back on. The on/off light is flashing. Its still connected to the left lug of the solenoid.

I don't know how shore power ties into this either
The Victron DC DC should not turn on until it sees a sufficient rise in voltage from the charge line, meaning the engine is running and the alternator is putting out sufficient charge voltage. There are several other ways to wire it but that is the most common.
 
Okay, getting into the parts I have never studied or done much looking! So don't take this to the bank!
But one we can say for pretty sure is that the big lugs on each side of the solenoid are not connected inside in any way without the small lugs to the coil being connected! Basicly makes the solenoid a set of lugs where cables can meet! Isolated points where cables can be placed.
What is the DC to DC meant to do? No info/experience on that point for me! But if the blue taped cable on left big lug feeds the jack pump and it is dead as well as the DC to DC, where does that DC gizmo get power to feed the jacks? Sounds like it is not getting power?
But I am way out of what I know much about! We may have to way for folks more experienced with the change to lithium to come along and add to the question. Is that a fuse holder sticking up that might need to be checked?
Have you tested that you still have chassis battery?

Wrote this up last night but got called and failed to get back to it!
what you currently have is the solenoid is no longer functioning. It is just being used as two points to tie wires down! If the two small white wires are not used, they should just be taped and stored ut of the way, not tied together.
But the main problem after things are changed is figuring out how and what the last person did and how they wanted it to work!
That gets into a whole different ballgame with lots of weird stuff being done. When the new change was done, did those folks get the other wiring change figured correctly?
Kind of having a set of parts and each person has to figure out what the last one did?
If they were building a car, did they put the engine in front or back, type situation, with no drawings to follow!
You have the right idea as well. All the work on this was done in Quartzsite and they'd have it fixed in 5 minutes, issue is I am 3000 miles away. I am on my way there soon but need to make sure I can dump tanks, use jacks/slides and not kill my chassis battery on the way there.
 
The Victron DC DC should not turn on until it sees a sufficient rise in voltage from the charge line, meaning the engine is running and the alternator is putting out sufficient charge voltage. There are several other ways to wire it but that is the most common.
I let the engine run a good 7-8 minutes while watching the battery app and nothing was coming through except 2 amps from cloudy day solar.

Its blinking every .8 sec which apparently means its working fine though?
every 3 sec is error
every 5 sec is turned off
 
I let the engine run a good 7-8 minutes while watching the battery app and nothing was coming through except 2 amps from cloudy day solar.

Its blinking every .8 sec which apparently means its working fine though?
every 3 sec is error
every 5 sec is turned off
Can you log into the DC-DC? Also, have you checked voltage at the charge wire to see if it is charging? Should be at least 13.8V.
 
Can you log into the DC-DC? Also, have you checked voltage at the charge wire to see if it is charging? Should be at least 13.8V.
I did log into the victron app, it said 14 volts but the epoch battery app didn't show it. When driving I can open the battery app and it'll show 25-28 amps coming in from the dc to dc (when its working)
 
Last edited:
ok so the last change makes everything work when plugged into shore power but when unplugged the 12v system will work but the inverter will not, it will start up and then show error and shut down. The inverter has the factory wiring
 
ok so the last change makes everything work when plugged into shore power but when unplugged the 12v system will work but the inverter will not, it will start up and then show error and shut down. The inverter has the factory wiring
Maybe your house battery is not charged enough? Does the inverter say what the error is? Most will shut down on low voltage. What happens if you try and use the inverter while the engine is running?
 
Maybe your house battery is not charged enough? Does the inverter say what the error is? Most will shut down on low voltage. What happens if you try and use the inverter while the engine is running?
House battery is a 460ah sitting at 70% / 313ah. I tested it and the 2 post junction the cable goes to as well as the fused link and they all had 12.8 volts. The app for the battery says 13.4 though. Is that an issue?

(house battery is not taking a charge from shore since these latest issues started, only thing charging it is solar)

I'll do more "unplugged" testing tomorrow when I leave the RV park. At this point I just want it useable enough to get back to AZ
 
It's not too easy to use voltage as a capacity estimate on Lipo and is not precise, but in general 12.8 volts is pretty low, like 20 to 30%. On the other hand 13.4V (after resting) would indicate near 100%.

If I understand you are using the battery app which communicates directly with the battery's internal BMS?

Lipo SOC.jpg
 
Last edited:

Try RV LIFE Pro Free for 7 Days

  • New Ad-Free experience on this RV LIFE Community.
  • Plan the best RV Safe travel with RV LIFE Trip Wizard.
  • Navigate with our RV Safe GPS mobile app.
  • and much more...
Try RV LIFE Pro Today
Back
Top