scangauge

2012 AI. Is this a safe coolant temperature after driving? I found out that sprinters run higher RPMs when driving so I just want to make sure my temperatures are normal. Thanks!

I installed a ScanGauge II on my Winnebago Brave built on the Ford F53 chassis, plugged directly into the OBD-II diagnostic connector under the dash. It took only a few minutes to connect and mount, and it’s been immediately useful. For those unfamiliar, the ScanGauge II gives you real-time...

I found some very old threads related to fuel mileage that mentioned Scangauge D. I have a 2003 FDTS with 400 ISL and about to pull the trigger for the Scangauge D, primarily to monitor transmission temps. My previous Safari coach had analog gauges for Transmission Temp and Oil Temp. I'm...

Hello helpful ones I have a 98 Fleetwood with Cummins ISB 5.9 + 6sp Allison. I recently installed scangauge to monitor fluid temp and trans. It’s not able to read the trans temp. And on the water temp it’s always in the 200-220 after just 15mins of local driving. However the gauge is in the...

Hello helpful ones on here. I have a 1998 Fleetwood discovery sitting on a freightliner chassis with a 5.9 L Cummins engine + 6sp Allison trans. I plan to install a scangauge D to monitor transmission temperature fluid and turbo boost pressure. Does anybody know that it will be compatible to...

Hi everybody, I have a 2008 Beaver Contessa with a 425 C9 Cat. Was wondering if one can use ScanGauge 3 realizing the ScanGauge 3 is for OBDII but if you used an adapter like they sell on amazon. "OBDII 6Pin 9Pin J1708 J1939 Cable for Truck" Wondering if it would it work ? or Has anyone...

I currently have an old SilverLeaf 200 EL still plugged in and operating but pixelated. I plugged my new ScanGuage into the 6 pin data port under the dash and get no readings or power. So… I plugged it into the rear data port by the motor and it works fine. Any ideas why the forward data port is...

I just installed a new ScanGaugeIII on my 2004 P32 Workhorse chassis, set up some monitors and it all was an easy install. I watched Kevin Caudil's videos which were very helpful. The engine ran about an hour at idle while I set it all up. He suggests the LTFT Bank 1, LTFT Bank 2 monitors should...

(This is a re-post from an old post - that still puzzles me): Speaking specifically about my 2018 24K F53 chassis with 3 valve 6.8L V10 engine and TorqShift 6 speed Transmission "6R140": I want to be able to see what gear my transmission is using at any given time, especially in mountain...

I have the above code on my scangauge B obd 11 on a recent trip. No dash lights or other warnings. 2002 HR endeavor diesel.It appears not to be a cummins isc cummins engine dtc. Any input would be helpful. Thx Fred B [email protected]

This instrument is the best thing since sliced bread for my older Monaco Exec. I apologize to those to already owning one, but I just gotta talk a bit. The analog temperature gauges on my Exec are not accurate and the ScanGauge D (for Diesel, ya know) quickly pointed that out. Additionally, this...

Anyone using it?

I am considering getting a Scangauge D for my coach. The chassis is a 2017 and I have read about some compatibility issues with the 2017 Freightliner M2 chassis. Comments included issues with the supplied connectors and once installed erroneous codes. Since I have read the comments on line...

Well, after having limped home several hundred miles and subsequently pulling the CAC for testing and cleaning, and then the radiator for repair ... everything is back in place; Started fine and seems to be running fine but still have the 'warning' light illuminated. I was unable to find my...

I am considering getting a ScanGauge 2 for my Holiday Rambler with a p32 Chassis. I see scattered mention on this forum of the ScanGauge2 which seems to be the most popular scanner among Workhorse owners but little info on how everyone uses theirs and what they monitor. So, how do you use yours...

I have been unablel to create a search that will find me a thread that discusses the basics of the scanguage II use for the GM 8.1 liter on a workhorse chassis P-32. How to get set up to read the X gauge additions. Can someone direct me to a source that will explain this to me?

I have some Sorry results from ScangaugeD. As you can see in my signature below I state I get 11+ MPG in my coach. I did a manual check over the last two days driving. (combination of hills and wind with no generator or aqua hot running). I'm getting 7.8. How can the ScangaugeD be so far off? Tim

Other than Amazon or Ultra RV does anyone have a good vendor to purchase from?

I have a 2006 Country Coach Inspire 360 with a CAT C9 400hp diesel pusher. The check engine light is coming on repeatedly. My Scangauge is showing codes 33 and 97. The engine power drops off for a few seconds and most times will pick up, occasionally shutting down. I can’t find any...

I’ve done some searching and don’t think I’ve found the info I’m looking for. Hooked up the ScanGauge today to monitor long term and short term fuel trims. Short term numbers look ok staying in the -10 to +10 range. Long term not looking so good. Cruising down the highway at 60 mph the...

Hi All, I’m trying to tackle my inoperable tachometer issue on my Cummins 6CTA 325hp powered CC Intrigue #10579 w Allison 6 speed transmission & Dynamax chassis. After an alternator failure a few years back, my tach has never worked the same since. Just replaced the tach again to specifically...

Speaking specifically about my 2018 24K F53 chassis with 3 valve 6.8L V10 engine and TorqShift 6 speed Transmission "6R140": I want to be able to see what gear my transmission is using at any given time, especially in mountain driving situations. I recently installed a ScanGauge II and it...

Looking hard at buying a Scangauge D for my motorhome, my question is about the display. The display dimensions seem small and my eyes are not what they use to be. I would like some feedback from someone using one as far as readability when mounted on the dashboard. If anyone from south...

Hello. I have a 2003 W22 8.1L Vortec with Allison 5speed 1000 Transmission. I purchased a Scangauge II and programed an X-gauge to monitor the transmission fluid temperature. The device works with the VPW protocol. As per GM specs, I entered the following parameters: TXD: 6C10F122194001 RXF...

Others have reported that this is a great product, but I am curious to know what specific displays are available before purchasing. We have 2005 Cummins ISL400 with an Allison M3000. Does anyone have one installed on this combination, and if so, can you tell me what it displays?