Thread Tools Search this Thread Display Modes
Old 06-16-2019, 09:52 AM   #1
Winnebago Camper
Join Date: Jan 2014
Location: Colorado Springs, CO
Posts: 29
Slide quit working

The driver's side kitchen slide out on my 2014 Destination 36RL has stopped working. The passenger side one still functions and my understanding is that both slides are on the same "hydraulic run"....that said, I read on one thread here about a blown fuse so I will go over to storage and verify that, but does anyone else have any experience or input to this issue? Thanks, Mike
mcumbie is offline   Reply With Quote
Old 06-16-2019, 11:29 AM   #2
Winnebago Camper
Join Date: Jan 2014
Location: Colorado Springs, CO
Posts: 29
updated info

Okay, so I have no blown fuses and the slide out controller module has no blinking fault code lights in play that would indicate any sort of motor failure. I did notice that the slide out is sitting flat on the floor of the inside of the 5th wheel and I am pretty sure it always had a slight gap between the floor and the slide when retracted just like my passenger side one does.

We did travel over some very bumpy interstate roads so I am hoping something just came out of adjustment height wise and it can just be dialed back into alignment when I take it in this Friday. Also hoping that my floor surface is not damaged since it had 2 days of towing in this position!!
mcumbie is offline   Reply With Quote
Old 06-29-2019, 06:22 PM   #3
Winnebago Camper
Join Date: Jan 2014
Location: Colorado Springs, CO
Posts: 29
Solution Iím happy that I didnít end up having a large repair bill but really disappointed in Winnebago because I donít think this issue should have ever been possible. The nut that holds the hydraulic ram of the slide out in place basically backed off and ultimately fell off, therefore causing the ram to drop and not able to push the slide out.

Props to Trailer Source for finding this and it only cost me $351.43 to fix...the biggest charge was 330$ to remove and reinstall the under belly to diagnose and address the issue. Just my opinion, I think this it should have been secured with a castle nut or some other type so it could not have fallen off and donít consider this something to be expected with normal wear and tear. So there ya go...end of story and my rig is back to normal operation.
mcumbie is offline   Reply With Quote
Old 07-04-2019, 07:05 AM   #4
Winnebago Owner
SocioSam's Avatar
Join Date: Jun 2013
Location: DeLand, Florida
Posts: 51
Happy you got it fixed. We had a similar issue when our driver side slide quit working. Lucky for us this happened about a week before warranty ended and we were unexpectedly on the road to help a cousin. Our problem was the motor burned out. Dealer who fixed it said Winnebago was having a problem putting installing motors too small for their slides.
SocioSam is offline   Reply With Quote


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off

Similar Threads
Thread Thread Starter Forum Replies Last Post
Booster switch has quit working GWayne Electrical | Charging, Solar and Electronics 23 07-21-2016 07:39 PM
Bedroom furnace quit working. Jeff35 Electrical | Charging, Solar and Electronics 11 02-15-2016 07:20 AM
Voyager 3 camera monitor quit working... Ramzfan Electrical | Charging, Solar and Electronics 6 07-02-2012 06:25 AM
GE Advantium Microwave Quit Working LK23 General Maintenance and Repair 10 10-06-2009 09:49 AM
Remotes for Jenson Radio quit working LCD Tech | Toys and Gear 6 08-13-2009 02:59 PM

» Featured Campgrounds

Reviews provided by


This website is not affiliated with or endorsed by Winnebago Industries or any of its affiliates. This is an independent, unofficial site.

Copyright 2002- Social Knowledge, LLC All Rights Reserved.

All times are GMT -6. The time now is 07:10 AM.

Powered by vBulletin® Version 3.8.8 Beta 1
Copyright ©2000 - 2019, vBulletin Solutions, Inc.